如何改變N76E003的頻率HIRC，以用于更準確的UART傳輸?
N76E003的HIRC頻率為16 MHz，常溫下偏差在1%以?xún)?nèi)。當用于38400以上baud rate的UART傳輸時，會因?yàn)?6 MHz無法除頻出38400 Hz的頻率，造成baud rate偏差過大，無法穩定傳輸。
此時用戶可以更改HIRC的頻率到16.588 MHz，就能產生精準的baud rate。
- 更改HIRC頻率的步驟如下：
1. Trim value = RCTRIM0(HIRCTRIM[8:1]) + RCTRIM1(HIRCTRIM[0])將Trim value–15可以調整HIRC的頻率為16.6 MHz。
2. 將計算值寫回RCTRIM0 和RCTRIM1，寫入后HIRC的更改會立即生效。
3. 每次上電后HIRC會恢復成16 MHz，使用者需要通過寫SFR來更改HIRC。
4. 按照16.588 MHz重新計算baud rate，再設定timer產生的baud rate就能符合標準baud rate。
- 范例程序如下：
sfr RCTRIM0 = 0x84;
sfr RCTRIM1 = 0x85;
bit BIT_TMP;
#define set_IAPEN BIT_TMP = EA; EA=0; TA=0xAA; TA=0x55; CHPCON |= SET_BIT0; EA= BIT_TMP
#define set_IAPGO BIT_TMP = EA; EA = 0; TA = 0xAA; TA = 0x55; IAPTRG |= SET_BIT0; EA = BIT_TMP
#define clr_IAPEN BIT_TMP = EA; EA = 0; TA = 0xAA; TA = 0x55; CHPCON &= ~SET_BIT0; EA=BIT_TMP
unsigned char hircmap0,hircmap1;
unsigned int trimvalue16bit;
void MODIFY_HIRC_VLAUE(void)
{
set_IAPEN;
IAPAL = 0x30;
IAPAH = 0x00;
IAPCN = READ_UID;
set_IAPGO;
hircmap0 = IAPFD;
IAPAL = 0x31;
IAPAH = 0x00;
set_IAPGO;
hircmap1 = IAPFD;
clr_IAPEN;
trimvalue16bit = ((hircmap0<<1)+(hircmap1&0x01));
trimvalue16bit = trimvalue16bit - 15;
hircmap1 = trimvalue16bit&0x01;
hircmap0 = trimvalue16bit>>1;
TA=0XAA;
TA=0X55;
RCTRIM0 = hircmap0;
TA=0XAA;
TA=0X55;
RCTRIM1 = hircmap1;
編輯：admin 最后修改時間：2018-03-09
